- All Known Implementing Classes:
DefaultBoundedRangeModel
Slider
s
and ProgressBar
s.
Defines four interrelated integer properties: minimum, maximum, extent
and value. These four integers define two nested ranges like this:
minimum <= value <= value+extent <= maximumThe outer range is
minimum,maximum
and the inner
range is value,value+extent
. The inner range
must lie within the outer one, i.e. value
must be
less than or equal to maximum
and value+extent
must greater than or equal to minimum
, and maximum
must be greater than or equal to minimum
.
There are a few features of this model that one might find a little
surprising. These quirks exist for the convenience of the
Swing BoundedRangeModel clients, such as Slider
and
ScrollBar
.
- The minimum and maximum set methods "correct" the other three properties to accommodate their new value argument. For example setting the model's minimum may change its maximum, value, and extent properties (in that order), to maintain the constraints specified above.
-
The value and extent set methods "correct" their argument to
fit within the limits defined by the other three properties.
For example if
value == maximum
,setExtent(10)
would change the extent (back) to zero. - The four BoundedRangeModel values are defined as Java Beans properties however Swing ChangeEvents are used to notify clients of changes rather than PropertyChangeEvents. This was done to keep the overhead of monitoring a BoundedRangeModel low. Changes are often reported at MouseDragged rates.
For an example of specifying custom bounded range models used by sliders, see Separable model architecture in A Swing Architecture Overview.
- Since:
- 1.2
- See Also:
-
Method Summary
Modifier and TypeMethodDescriptionvoid
Adds a ChangeListener to the model's listener list.int
Returns the model's extent, the length of the inner range that begins at the model's value.int
Returns the model's maximum.int
Returns the minimum acceptable value.int
getValue()
Returns the model's current value.boolean
Returns true if the current changes to the value property are part of a series of changes.void
Removes a ChangeListener from the model's listener list.void
setExtent
(int newExtent) Sets the model's extent.void
setMaximum
(int newMaximum) Sets the model's maximum to newMaximum.void
setMinimum
(int newMinimum) Sets the model's minimum to newMinimum.void
setRangeProperties
(int value, int extent, int min, int max, boolean adjusting) This method sets all of the model's data with a single method call.void
setValue
(int newValue) Sets the model's current value tonewValue
ifnewValue
satisfies the model's constraints.void
setValueIsAdjusting
(boolean b) This attribute indicates that any upcoming changes to the value of the model should be considered a single event.
-
Method Details
-
getMinimum
int getMinimum()Returns the minimum acceptable value.- Returns:
- the value of the minimum property
- See Also:
-
setMinimum
void setMinimum(int newMinimum) Sets the model's minimum to newMinimum. The other three properties may be changed as well, to ensure that:minimum <= value <= value+extent <= maximum
Notifies any listeners if the model changes.
- Parameters:
newMinimum
- the model's new minimum- See Also:
-
getMaximum
int getMaximum()Returns the model's maximum. Note that the upper limit on the model's value is (maximum - extent).- Returns:
- the value of the maximum property.
- See Also:
-
setMaximum
void setMaximum(int newMaximum) Sets the model's maximum to newMaximum. The other three properties may be changed as well, to ensure thatminimum <= value <= value+extent <= maximum
Notifies any listeners if the model changes.
- Parameters:
newMaximum
- the model's new maximum- See Also:
-
getValue
int getValue()Returns the model's current value. Note that the upper limit on the model's value ismaximum - extent
and the lower limit isminimum
.- Returns:
- the model's value
- See Also:
-
setValue
void setValue(int newValue) Sets the model's current value tonewValue
ifnewValue
satisfies the model's constraints. Those constraints are:minimum <= value <= value+extent <= maximum
Otherwise, ifnewValue
is less thanminimum
it's set tominimum
, if its greater thanmaximum
then it's set tomaximum
, and if it's greater thanvalue+extent
then it's set tovalue+extent
.When a BoundedRange model is used with a scrollbar the value specifies the origin of the scrollbar knob (aka the "thumb" or "elevator"). The value usually represents the origin of the visible part of the object being scrolled.
Notifies any listeners if the model changes.
- Parameters:
newValue
- the model's new value- See Also:
-
setValueIsAdjusting
void setValueIsAdjusting(boolean b) This attribute indicates that any upcoming changes to the value of the model should be considered a single event. This attribute will be set to true at the start of a series of changes to the value, and will be set to false when the value has finished changing. Normally this allows a listener to only take action when the final value change in committed, instead of having to do updates for all intermediate values.Sliders and scrollbars use this property when a drag is underway.
- Parameters:
b
- true if the upcoming changes to the value property are part of a series
-
getValueIsAdjusting
boolean getValueIsAdjusting()Returns true if the current changes to the value property are part of a series of changes.- Returns:
- the valueIsAdjustingProperty.
- See Also:
-
getExtent
int getExtent()Returns the model's extent, the length of the inner range that begins at the model's value.- Returns:
- the value of the model's extent property
- See Also:
-
setExtent
void setExtent(int newExtent) Sets the model's extent. The newExtent is forced to be greater than or equal to zero and less than or equal to maximum - value.When a BoundedRange model is used with a scrollbar the extent defines the length of the scrollbar knob (aka the "thumb" or "elevator"). The extent usually represents how much of the object being scrolled is visible. When used with a slider, the extent determines how much the value can "jump", for example when the user presses PgUp or PgDn.
Notifies any listeners if the model changes.
- Parameters:
newExtent
- the model's new extent- See Also:
-
setRangeProperties
void setRangeProperties(int value, int extent, int min, int max, boolean adjusting) This method sets all of the model's data with a single method call. The method results in a single change event being generated. This is convenient when you need to adjust all the model data simultaneously and do not want individual change events to occur.- Parameters:
value
- an int giving the current valueextent
- an int giving the amount by which the value can "jump"min
- an int giving the minimum valuemax
- an int giving the maximum valueadjusting
- a boolean, true if a series of changes are in progress- See Also:
-
addChangeListener
Adds a ChangeListener to the model's listener list.- Parameters:
x
- the ChangeListener to add- See Also:
-
removeChangeListener
Removes a ChangeListener from the model's listener list.- Parameters:
x
- the ChangeListener to remove- See Also:
-